Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
We have stumbled upon this article involving Tools You Need to Install a New Bathtub down the page on the net and concluded it made sense to write about it with you in this article.
Installing a bath tub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably hard job. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the task is within a residence handyman's skills, although you will require a helper to vacate the old bathtub and embeded in the brand-new one. Make sure you have actually qualified yourself for the work as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is much better to consider utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a brand-new bathtub and do not need to change the plan of your previous supply of water pipelines.
Your devices and product checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washers are in place between the tap and the sink. Secure the tap in place with the producer given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub until the level checks out level.
To set up taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and also inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and the regular electrical outlet for leakages.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the tub has actually been utilized at least when as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about Installing A Bathtub? Post feedback directly below. We will be delighted to find out your opinion about this write-up. We hope that you come back again before long. Please set aside a second to share this article if you enjoyed reading it. Thanks a lot for your time. Please come by our website back soon.
Contact Report this page